Call us today on (407) 859-1119 or email [email protected]

ROLL FORMING MACHINES LLC
Browse Pages
Browse by Category
Accurate Length Control on Roll Form Cut-Offs

ArticlesAccurate Length Control on Roll Form Cut-Offs

Accurate Length Control on Roll Form Cut-Offs

There is no doubt that the invention of high-speed, modern roll-forming machines has changed the landscape

Posted by Ben Browne on Wednesday, March 29, 2023

For any industry requiring repetitive linear metal shapes to be produced en masse. The consistency of shapes created, as well as the required time it takes to manufacture them, makes investing in a roll-forming machine a no-brainer for many businesses.

However, one of the advantages of parts produced by more old-fashioned press breakers was that consistency in the length of each part was more easily achievable. While early roll formers could produce a consistent profile and parts of varying lengths, in the earliest versions, the machines would be stopped, and the sheet cut to size with a chop saw or stationary die. This impacted the efficiency of the machine and made it difficult to cut the sheet to precisely the same length each time. Variance in the timing, even by a fraction, could result in non-uniform parts.

Because of the numerous variables, the press could not be guaranteed to stop at the absolute Top Dead Center; this would, in turn, affect the timing of the following stroke as compared to the previous stroke.

Another massive variable would be the line air pressure. A large draw from the air system would often require an adjustment of the clutch's limit switch, enabling the air cylinder to move slightly sooner to help ensure the die line was up to speed. The lubrication of slides under the cut-off die, the speed of the press, and the distance the die had to travel in the downward stroke before cutting were all other factors that could result in inconsistent cut-off lengths.

However, advances in technology were made over time to ensure that more accurate length control on roll form cut-offs was possible. Roll-formed sections having more rigidity and being crafted from 20-gage material meant they could strike a preset arm as opposed to a limit switch that essentially pulled the cut-off die along with it. Because the die travelled with the section, the press was then activated. This meant lengths were accurately cut over and over again.

Advances in technology

The invention of the 1960s air press somewhat changed the game in terms of cut-off precision. Compared to mechanical presses, the speed at which air presses worked was impressive, reducing the amount of time between the roll-formed sheet striking the length limit switch and the section being cut. Because of this, a means to prevent the press from moving too far and damaging the die was crucial. Down stops were used to transfer the excess energy of the press stroke into the base - a good solution, though, resulted in the floor under the machine becoming work over time thanks to the repeated shock waves.

While air presses were advantageous in accurately cutting-off light gauge roll-formed sections at high speeds, the deterioration of the floor underneath the machine meant there could have been a better solution.

Enter high-speed hydraulics and shear blades - a combination seen on many contemporary roll formers today. A hydraulic piston attached to the shear blade controls the stroke length, which is triggered based on the length of time the hydraulic valve remains open. Because the shear blade is cut to the shape of the desired part, the length of time required for the die to travel to the shear is almost imperceptible. Being able to adjust the amount of time the valves open meant very accurate adjustments could be made.

Machine controllers then also made further refinements possible as they could compensate for many factors in the complete press cut-off cycle that could affect the accuracy of the cut.

Limit switches have also been replaced in contemporary machines, which now use Rotary Transducers. These make contact with the material with a precisely sized wheel, driving a finely graduated optical reader while the material passes underneath. Doing so can produce length accuracies of +/- 1/32″

At Roll Forming LLC, we invest in quality Roll Forming machines that employ the latest technology to ensure accurate parts are produced at speed. If you are looking for a roll-forming machine for your business, browse our range of get in touch with our team today.

Muti Profile Roll Forming Machines 

Muti Profile Roll Forming Machines 

Posted on Thursday, May 25, 2023

Multi-profile roll forming lines, are industrial machines used to manufacture multiple profiles

Shear blade surface grinding

Shear blade surface grinding

Posted on Thursday, May 25, 2023

Sharpen and restore the cutting surface of shear blades.

Stud and Track Machines for Dry Wall

Stud and Track Machines for Dry Wall

Posted on Thursday, May 25, 2023

How do Stud and Track machines for dry wall work?

Silo Roll Forming Machines

Silo Roll Forming Machines

Posted on Thursday, May 25, 2023

Silo roll forming machines are specialized industrial machines used in the manufacturing of silos.

Roll Forming Machines LLC 10895 Rocket Blvd, Suite 120, Orlando, FL 32824, USA

Phone USA (407) 859-1119

Email [email protected]

Copyright 2023 © Rollforming Machines LLC.